Artificial aluminum foam material, manipulator clamping on both
sides of the glue position, servo motor drives the aluminum foam
automatic into slurry, squeegee automatically closed, the aluminum
foam automatic positioning plastic, manipulator automatically rise,
rise, in the process of slurry pool 1 to reverse rolling, will
reverse pressure into the foam aluminum paste, even thickness on
both sides of the battery are formed by squeegee plate.
3.3 System introduction
3.3.1. Frame housing system: The frame adopts square-pass welding
structure, which is firm and reliable, and the housing adopts
aluminum profile and plexiglass structure
3.3.2 Slurry pool system: Slurry pool adopts T-structure design to
reduce slurry waste as much as possible. There is a pair of reverse
rotating extrusion roller in the slurry pool to squeeze slurry onto
aluminum foam at an adjustable speed.
There is a unloading valve below the size pool, which is convenient
to remove the residual material and clean the size pool from below.
Removable front and rear panels for easy cleaning.
3.3.3 Scraper system: The servo motor drives the two sides of the
scraper to move. When the manipulator moves down, it opens. When
the aluminum foam is completely immersed in the slurry, the servo
motor drives the scraper to close, and the closing size is set on
the touch screen.
After closing, the straightening comb is pressed against the
aluminum foam, and the aluminum foam is straightened. The size of
the pulping board is set as the required size.
3.3.4 Manipulator system: the servo motor drives the ball screw to
drive the finger clamp to move up and down. The moving distance can
be set on the touch screen.
Manually put the pole piece of adhesive tape into the finger clip,
press the start button, the cylinder clamps the pole piece, and the
servo electrode drives the pole piece down.
7. Energy media
7.1 the power supply
7.1.1 Voltage: AC380V± 10% in single phase instantaneous change of
less than 0.5s.
7.1.2 Frequency: 50Hz±1Hz.
7.1.3 power: 3 kw
7.2 the air
7.2.1 Pressure: Air source party A shall provide dry air of
7.2.2 Capacity: 3L/min.
8,General configuration and standard of equipment
8.1 The device is equipped with PLC and communication interface
with HMI (RS232 or RS485) to check the status and parameter
Settings of the machine.
8.2 The appearance color of the equipment is the international
standard warm gray 1C.
8.3 Measured at 100mm away from the outside wall of the machine,
noise of the equipment ≤ 70dB.
8.4 The equipment complies with the safety standards of relevant
national equipment and all safety standards and requirements as
required by Party A's relevant safety code.
9,. Quality assurance and after-sales service
11.1 The warranty period of the equipment shall be one year from
the date of final acceptance of the equipment.
During the period, Party B shall be responsible for the free
maintenance of equipment and the free provision of equipment
In case of equipment abnormalities, Party B shall respond within 4
hours upon receipt of party A's notice, provide solutions within 24
hours, arrive at the site (within the province) within 48 hours,
and repair within a reasonable time.
After the end of the warranty period, Party B shall still be
responsible for the maintenance of the equipment and only charge
for working hours and transportation and accommodation.
Party B shall only charge the cost for the replacement and purchase
of the relevant parts of the equipment.
11.2 During the warranty period, the following conditions shall not
apply: in case of damage of the equipment caused by earthquake,
typhoon, lightning strike, flood, fire and other disasters beyond
human resistance; in case of man-made damage by Party A, the
damaged parts shall be consumed under normal conditions as
stipulated in the technical agreement.
11.3 Force Majeure: Force majeure refers to the objective
circumstances that are unforeseeable, insurmountable and
unavoidable at the time of the conclusion of the Contract by both
If Party B fails to deliver the goods or delays the delivery due to
force majeure, Party B shall immediately notify Party A and send
the accident certificate issued by the local government authorities
to the other party within 14 days after the occurrence of the
After the event of force majeure is eliminated, if the party having
the event of force majeure is able to continue to perform the
contract, it shall immediately notify the other party in writing,
and the demander shall provide a written notice for reply.
11.4 party b's personnel (and party b choose transport party) at
the scene of the party a, should strictly abide by the relevant
national laws, regulations, and party a about the environment and
occupational health and safety requirements, should not have the
behavior of the pollution and damage to the environment, should be
worn at the same time relevant protective equipment, and can't
interfere with party a's environmental health and safety operation
personnel to exercise their duties.